For example, I’ll take the Ubiquiti Rocket M5 configuration file and describe some parameters (with other Ubiquiti equipment these parameters can be identical:
aaa.1.br.devname=br0 (bridge device name) aaa.1.devname=ath0 (WiFi name of the device) aaa.1.driver=madwifi (driver WiFi) aaa.1.radius.acct.1.status=disabled (use of Radius accounts for authorization) aaa.1.radius.auth.1.status=disabled (using authorization through Radius server) aaa.1.radius.macacl.status=disabled (using authorization for mac addresses via Radius server) aaa.1.ssid=mimo (access point name) aaa.1.status=enabled (radio module status, enabled - on, disabled - off) aaa.1.wpa.1.pairwise=CCMP (signal encryption protocol) aaa.1.wpa.key.1.mgmt=WPA-PSK (encryption type) aaa.1.wpa.mode=2 (protocol version, 2 — WPA2-PSK) aaa.1.wpa.psk=12345678 (encryption key, password for Wi-Fi) aaa.status=enabled (activation of all of the above) airview.tcp_port=18888 (port AirView) bridge.1.devname=br0 (bridge device) bridge.1.fd=1 bridge.1.port.1.devname=eth0 (first device name, eth0 is LAN) ) bridge.1.port.1.status=enabled (turning on/off the above device) bridge.1.port.2.devname=ath0 (the name of the second device, ath0 is Wi-Fi) bridge.1.port.2.status=enabled (turning on/off the above device) bridge.1.status=enabled (enable/disable bridge 1) bridge.1.stp.status=disabled (using STP (Spanning Tree Protocol) bridge.status=enabled dhcpc.1.devname=br0 (name of the device on which the first dhcp client will run) dhcpc.1.status=disabled (enable/disable the above dhcp client) dhcpc.status=disabled (using dhcp client) dhcpd.status=disabled (using dhcp server) discovery.cdp.status=enabled (using cdp (Cisco Discovery Protocol) device discovery) discovery.status=enabled (enable device discovery on the network) dyndns.status=disabled (using dyndns client) ebtables.status=enabled (use of built-in firewall) ebtables.sys.arpnat.1.devname=ath0 ebtables.sys.arpnat.1.status=enabled ebtables.sys.arpnat.status=disabled ebtables.sys.eap.1.devname=ath0 ebtables.sys.eap.1.status=enabled ebtables.sys.eap.status=enabled ebtables.sys.status=enabled gui.language=en_US (web interface language) httpd.https.status=disabled (using https) httpd.port=80 (port httpd) httpd.session.timeout=900 (http session timeout) httpd.status=enabled (using httpd) netconf.1.autoip.status=disabled (whether to receive IP automatically) netconf.1.autoneg=enabled (auto-negotiation of connection speed) netconf.1.devname=eth0 (device name used) netconf.1.hwaddr.mac= (mac address device) netconf.1.hwaddr.status=disabled (enabled - use of the above mac address or native) netconf.1.ip=0.0.0.0 (Interface IP address) netconf.1.mtu=1500 (MTU interface size) netconf.1.netmask=255.255.255.0 (interface network mask) netconf.1.promisc=enabled netconf.1.role=bridge_port netconf.1.status=enabled netconf.1.up=enabled netconf.2.allmulti=disabled (multicast packet allow) netconf.2.autoip.status=disabled (whether to receive IP automatically) netconf.2.devname=ath0 (wireless device name) netconf.2.hwaddr.mac= (mac address wireless interface) netconf.2.hwaddr.status=disabled (enabled - use of the above mac address or native) netconf.2.ip=0.0.0.0 (Wireless IP Address) netconf.2.mtu=1500 (MTU size of the wireless interface) netconf.2.netmask=255.255.255.0 netconf.2.promisc=enabled netconf.2.role=bridge_port netconf.2.status=enabled netconf.2.up=enabled netconf.3.autoip.status=disabled netconf.3.devname=br0 netconf.3.hwaddr.mac= netconf.3.hwaddr.status=disabled netconf.3.ip=10.0.0.100 netconf.3.mtu=1500 netconf.3.netmask=255.255.255.0 netconf.3.role=mlan netconf.3.status=enabled netconf.3.up=enabled netconf.status=enabled (enable all network interfaces) netmode=bridge (network mode) ntpclient.status=disabled (using NTP client) ppp.status=disabled (using ppp) pwdog.status=disabled (using ping watchdog) radio.1.ack.auto=enabled (automatic detection of ack timeout) radio.1.ackdistance=13350 (distance between points in meters) radio.1.acktimeout=110 (ack timeout) radio.1.airsync.ip= (irsync ip) radio.1.airsync.mode= radio.1.airsync.port= radio.1.airsync.slot.down= radio.1.airsync.slot.override=disabled radio.1.airsync.slot.up= radio.1.airsync.status=disabled (using airsync) radio.1.ampdu.bytes=50000 radio.1.ampdu.frames=32 (number of AMPDU frames) radio.1.ampdu.status=enabled radio.1.antenna.gain=24 radio.1.antenna.id= radio.1.cable.loss=0 radio.1.chanbw=0 (bandwidth limit) radio.1.chanshift=0 (using chaneel shifting for frequency shifting) radio.1.clksel=1 (channel width, 1 = 20 МГц, 2 = 10 МГц, 4 = 5 МГц) radio.1.countrycode=511 radio.1.cwm.enable=0 radio.1.cwm.mode=2 radio.1.devname=ath0 (wireless device name) radio.1.dfs.status=enabled (use of DFS - automatic adjustment of frequency/power, useful when noise or changes in weather conditions) radio.1.forbiasauto=1 radio.1.freq=2452 radio.1.ieee_mode=11nght40plus radio.1.low_txpower_mode=disabled (transmitter low power mode) radio.1.mcastrate=15 (maximum bandwidth for multicast packets) radio.1.mode=master (point mode, master - main) radio.1.obey=disabled radio.1.polling=enabled radio.1.polling_fh=0 radio.1.polling_fh_announce_cnt=10 radio.1.polling_fh_time=3000 radio.1.pollingnoack=0 radio.1.pollingpri= radio.1.rate.auto=enabled (automatic adjustment of data rate) radio.1.rate.mcs=15 radio.1.reg_obey=disabled radio.1.rts=off (using rts (request to send a package)) radio.1.status=enabled radio.1.subsystemid=0xe1b2 radio.1.thresh62a= radio.1.thresh62b= radio.1.thresh62g= radio.1.txpower=20 (transmitter power in db) radio.countrycode=511 radio.rate_module=ewma_ht radio.status=enabled resolv.host.1.name= resolv.host.1.status=enabled resolv.nameserver.1.ip= (first DNS server address) resolv.nameserver.1.status=disabled resolv.nameserver.2.ip= (second DNS server address) resolv.nameserver.2.status=disabled resolv.nameserver.status=disabled (use of DNS servers) resolv.status=disabled (translation of domain names into addresses) route.1.comment= (comment for the first route) route.1.devname=br0 (device name for the first route) route.1.gateway=10.0.0.1 (gateway for the first device) route.1.ip=0.0.0.0 (route end address) route.1.netmask=0 route.1.status=enabled (use of the specified route) route.status=enabled (use of routes) snmp.community=public snmp.contact=ixnfo.com snmp.location=UA snmp.status=enabled sshd.auth.passwd=enabled (ssh password authentication) sshd.port=22 sshd.status=enabled syslog.remote.status= syslog.status=enabled system.button.reset=enabled (use the reset button to the standard configuration) system.cfg.version=65541 system.date.status=disabled system.date.timestamp= system.eirp.status=disabled system.latitude= system.longitude= system.timezone=GMT telnetd.status=disabled (using telnet) update.check.status=enabled (check for new software versions) users.1.name=admin (first username) users.1.password=password (password of the first user in the hash) users.1.status=enabled (first user status) users.2.status=disabled (second user status) users.status=enabled (on/off all users) vlan.status=disabled (using vlan) wireless.1.addmtikie=enabled wireless.1.ap= wireless.1.authmode=1 wireless.1.autowds=disabled (station wds) wireless.1.compression=0 wireless.1.devname=ath0 wireless.1.fastframes=0 wireless.1.frameburst=0 wireless.1.hide_ssid=disabled wireless.1.l2_isolation=disabled (isolating clients from each other) wireless.1.mac_acl.policy=allow (authorization policy for poppies, allow/deny) wireless.1.mac_acl.status=disabled (enable/disable access restriction for connecting clients via ACL AC) wireless.1.macclone=disabled wireless.1.scan_list.channels= (list of channels for ap search) wireless.1.scan_list.status=disabled (use of the above frequency list) wireless.1.security.type=none wireless.1.sens=0 wireless.1.signal_led1=94 (signal level at which LED 1 should light up) wireless.1.signal_led2=80 (signal level at which LED 2 should light up) wireless.1.signal_led3=73 (signal level at which LED 3 should light up) wireless.1.signal_led4=65 (signal level at which LED 4 should light up) wireless.1.signal_led_status=enabled (use of signal indication LEDs) wireless.1.ssid=mimo (ssid ap) wireless.1.status=enabled (use of a wireless network) wireless.1.wds.1.peer= wireless.1.wds.2.peer= wireless.1.wds.3.peer= wireless.1.wds.4.peer= wireless.1.wds.5.peer= wireless.1.wds.6.peer= wireless.1.wds.status=disabled (using WDS) wireless.1.wmm=enabled (QoS) wireless.1.wmmlevel= (QoS level) wireless.status=enabled (using Wi-Fi) wpasupplicant.device.1.status=disabled wpasupplicant.profile.1.network.1.psk=123456789 (authorization key / wifi password) wpasupplicant.status=disabled
See also my article:
Ubiquiti management via SSH