Ubiquiti Rocket M5 configuration file description

aaa.1.br.devname=br0 (bridge device name)
aaa.1.devname=ath0 (WiFi name of the device)
aaa.1.driver=madwifi (driver WiFi)
aaa.1.radius.acct.1.status=disabled (use of Radius accounts for authorization)
aaa.1.radius.auth.1.status=disabled (using authorization through Radius server)
aaa.1.radius.macacl.status=disabled (using authorization for mac addresses via Radius server)
aaa.1.ssid=mimo (access point name)
aaa.1.status=enabled (radio module status, enabled - on, disabled - off)
aaa.1.wpa.1.pairwise=CCMP (signal encryption protocol)
aaa.1.wpa.key.1.mgmt=WPA-PSK (encryption type)
aaa.1.wpa.mode=2 (protocol version, 2 — WPA2-PSK)
aaa.1.wpa.psk=12345678 (encryption key, password for Wi-Fi)
aaa.status=enabled (activation of all of the above)
airview.tcp_port=18888 (port AirView)
bridge.1.devname=br0 (bridge device)
bridge.1.fd=1
bridge.1.port.1.devname=eth0 (first device name, eth0 is LAN) )
bridge.1.port.1.status=enabled (turning on/off the above device)
bridge.1.port.2.devname=ath0 (the name of the second device, ath0 is Wi-Fi)
bridge.1.port.2.status=enabled (turning on/off the above device)
bridge.1.status=enabled (enable/disable bridge 1)
bridge.1.stp.status=disabled (using STP (Spanning Tree Protocol)
bridge.status=enabled
dhcpc.1.devname=br0 (name of the device on which the first dhcp client will run)
dhcpc.1.status=disabled (enable/disable the above dhcp client)
dhcpc.status=disabled (using dhcp client)
dhcpd.status=disabled (using dhcp server)
discovery.cdp.status=enabled (using cdp (Cisco Discovery Protocol) device discovery)
discovery.status=enabled (enable device discovery on the network)
dyndns.status=disabled (using dyndns client)
ebtables.status=enabled (use of built-in firewall)
ebtables.sys.arpnat.1.devname=ath0
ebtables.sys.arpnat.1.status=enabled
ebtables.sys.arpnat.status=disabled
ebtables.sys.eap.1.devname=ath0
ebtables.sys.eap.1.status=enabled
ebtables.sys.eap.status=enabled
ebtables.sys.status=enabled
gui.language=en_US (web interface language)
httpd.https.status=disabled (using https)
httpd.port=80 (port httpd)
httpd.session.timeout=900 (http session timeout)
httpd.status=enabled (using httpd)
netconf.1.autoip.status=disabled (whether to receive IP automatically)
netconf.1.autoneg=enabled (auto-negotiation of connection speed)
netconf.1.devname=eth0 (device name used)
netconf.1.hwaddr.mac= (mac address device)
netconf.1.hwaddr.status=disabled (enabled - use of the above mac address or native)
netconf.1.ip=0.0.0.0 (Interface IP address)
netconf.1.mtu=1500 (MTU interface size)
netconf.1.netmask=255.255.255.0 (interface network mask)
netconf.1.promisc=enabled
netconf.1.role=bridge_port
netconf.1.status=enabled
netconf.1.up=enabled
netconf.2.allmulti=disabled (multicast packet allow)
netconf.2.autoip.status=disabled (whether to receive IP automatically)
netconf.2.devname=ath0 (wireless device name)
netconf.2.hwaddr.mac= (mac address wireless interface)
netconf.2.hwaddr.status=disabled (enabled - use of the above mac address or native)
netconf.2.ip=0.0.0.0 (Wireless IP Address)
netconf.2.mtu=1500 (MTU size of the wireless interface)
netconf.2.netmask=255.255.255.0
netconf.2.promisc=enabled
netconf.2.role=bridge_port
netconf.2.status=enabled
netconf.2.up=enabled
netconf.3.autoip.status=disabled
netconf.3.devname=br0
netconf.3.hwaddr.mac=
netconf.3.hwaddr.status=disabled
netconf.3.ip=10.0.0.100
netconf.3.mtu=1500
netconf.3.netmask=255.255.255.0
netconf.3.role=mlan
netconf.3.status=enabled
netconf.3.up=enabled
netconf.status=enabled (enable all network interfaces)
netmode=bridge (network mode)
ntpclient.status=disabled (using NTP client)
ppp.status=disabled (using ppp)
pwdog.status=disabled (using ping watchdog)
radio.1.ack.auto=enabled (automatic detection of ack timeout)
radio.1.ackdistance=13350 (distance between points in meters)
radio.1.acktimeout=110 (ack timeout)
radio.1.airsync.ip= (irsync ip)
radio.1.airsync.mode=
radio.1.airsync.port=
radio.1.airsync.slot.down=
radio.1.airsync.slot.override=disabled
radio.1.airsync.slot.up=
radio.1.airsync.status=disabled (using airsync)
radio.1.ampdu.bytes=50000
radio.1.ampdu.frames=32 (number of AMPDU frames)
radio.1.ampdu.status=enabled
radio.1.antenna.gain=24
radio.1.antenna.id=
radio.1.cable.loss=0
radio.1.chanbw=0 (bandwidth limit)
radio.1.chanshift=0 (using chaneel shifting for frequency shifting)
radio.1.clksel=1 (channel width, 1 = 20 МГц, 2 = 10 МГц, 4 = 5 МГц)
radio.1.countrycode=511
radio.1.cwm.enable=0
radio.1.cwm.mode=2
radio.1.devname=ath0 (wireless device name)
radio.1.dfs.status=enabled (use of DFS - automatic adjustment of frequency/power, useful when noise or changes in weather conditions)
radio.1.forbiasauto=1
radio.1.freq=2452
radio.1.ieee_mode=11nght40plus
radio.1.low_txpower_mode=disabled (transmitter low power mode)
radio.1.mcastrate=15 (maximum bandwidth for multicast packets)
radio.1.mode=master (point mode, master - main)
radio.1.obey=disabled
radio.1.polling=enabled
radio.1.polling_fh=0
radio.1.polling_fh_announce_cnt=10
radio.1.polling_fh_time=3000
radio.1.pollingnoack=0
radio.1.pollingpri=
radio.1.rate.auto=enabled (automatic adjustment of data rate)
radio.1.rate.mcs=15
radio.1.reg_obey=disabled
radio.1.rts=off (using rts (request to send a package))
radio.1.status=enabled
radio.1.subsystemid=0xe1b2
radio.1.thresh62a=
radio.1.thresh62b=
radio.1.thresh62g=
radio.1.txpower=20 (transmitter power in db)
radio.countrycode=511
radio.rate_module=ewma_ht
radio.status=enabled
resolv.host.1.name=
resolv.host.1.status=enabled
resolv.nameserver.1.ip= (first DNS server address)
resolv.nameserver.1.status=disabled
resolv.nameserver.2.ip= (second DNS server address)
resolv.nameserver.2.status=disabled
resolv.nameserver.status=disabled (use of DNS servers)
resolv.status=disabled (translation of domain names into addresses)
route.1.comment= (comment for the first route)
route.1.devname=br0 (device name for the first route)
route.1.gateway=10.0.0.1 (gateway for the first device)
route.1.ip=0.0.0.0 (route end address)
route.1.netmask=0
route.1.status=enabled (use of the specified route)
route.status=enabled (use of routes)
snmp.community=public
snmp.contact=ixnfo.com
snmp.location=UA
snmp.status=enabled
sshd.auth.passwd=enabled (ssh password authentication)
sshd.port=22
sshd.status=enabled
syslog.remote.status=
syslog.status=enabled
system.button.reset=enabled (use the reset button to the standard configuration)
system.cfg.version=65541
system.date.status=disabled
system.date.timestamp=
system.eirp.status=disabled
system.latitude=
system.longitude=
system.timezone=GMT
telnetd.status=disabled (using telnet)
update.check.status=enabled (check for new software versions)
users.1.name=admin (first username)
users.1.password=password (password of the first user in the hash)
users.1.status=enabled (first user status)
users.2.status=disabled (second user status)
users.status=enabled (on/off all users)
vlan.status=disabled (using vlan)
wireless.1.addmtikie=enabled
wireless.1.ap=
wireless.1.authmode=1
wireless.1.autowds=disabled (station wds)
wireless.1.compression=0
wireless.1.devname=ath0
wireless.1.fastframes=0
wireless.1.frameburst=0
wireless.1.hide_ssid=disabled
wireless.1.l2_isolation=disabled (isolating clients from each other)
wireless.1.mac_acl.policy=allow (authorization policy for poppies, allow/deny)
wireless.1.mac_acl.status=disabled (enable/disable access restriction for connecting clients via ACL AC)
wireless.1.macclone=disabled
wireless.1.scan_list.channels= (list of channels for ap search)
wireless.1.scan_list.status=disabled (use of the above frequency list)
wireless.1.security.type=none
wireless.1.sens=0
wireless.1.signal_led1=94 (signal level at which LED 1 should light up)
wireless.1.signal_led2=80 (signal level at which LED 2 should light up)
wireless.1.signal_led3=73 (signal level at which LED 3 should light up)
wireless.1.signal_led4=65 (signal level at which LED 4 should light up)
wireless.1.signal_led_status=enabled (use of signal indication LEDs)
wireless.1.ssid=mimo (ssid ap)
wireless.1.status=enabled (use of a wireless network)
wireless.1.wds.1.peer=
wireless.1.wds.2.peer=
wireless.1.wds.3.peer=
wireless.1.wds.4.peer=
wireless.1.wds.5.peer=
wireless.1.wds.6.peer=
wireless.1.wds.status=disabled (using WDS)
wireless.1.wmm=enabled (QoS)
wireless.1.wmmlevel= (QoS level)
wireless.status=enabled (using Wi-Fi)
wpasupplicant.device.1.status=disabled
wpasupplicant.profile.1.network.1.psk=123456789 (authorization key / wifi password)
wpasupplicant.status=disabled