Restore Huawei SmartAX MA5600 Configuration

On the test, I will give an example of creating a backup of the Huawei SmartAX MA5683T configuration to a TFTP server, as well as its restoration.
Recovery is often useful when you need to quickly return to the previous configuration or to make massive changes to the configuration or to profiles that are active and used by the ONT.
OLT reboot is required.

Continue reading “Restore Huawei SmartAX MA5600 Configuration”

Huawei Quidway S2300 firmware upgrade via BOOTROM MENU

I will give an example of updating the firmware of the Huawei Quidway S2326TP-EI switch via BOOTROM MENU.

Connect to the switch console, standard speed 9600.
When you turn on the switch, immediately press the Ctrl + B key combination to enter the BOOTROM MENU.
Enter the switch password, usually:
Continue reading “Huawei Quidway S2300 firmware upgrade via BOOTROM MENU”

Installing Huawei iManager U2000 NMS on Windows Server

I will describe the procedure for installing the Huawei iManager U2000 NMS server software on a Windows Server:

1) Run on behalf of the administrator file install.bat

2) Copyright. We read and agree with the license agreement by selecting “I accept the terms”.
Continue reading “Installing Huawei iManager U2000 NMS on Windows Server”

Block third-party DHCP servers on the Huawei Quidway S2300 (DHCP Snooping)

I will give an example of how on the Huawei Quidway S2300 switch (using the S2326TP-EI as an example) to allow receiving DHCP responses from the uplink port and prohibiting client responses.

Continue reading “Block third-party DHCP servers on the Huawei Quidway S2300 (DHCP Snooping)”

Configuring Huawei Quidway S3900 Switches

For example, take the switch Huawei Quidway S3928P-EI, the settings are essentially suitable for the entire Huawei Quidway S3900 series, but may differ slightly depending on the firmware version. If something fails to register, then you can see the options for the teams by typing a question mark after a space after any command.

At me at switching-on of the switch, through the console the following characteristics were displayed:

Creation date: Aug 25 2006
CPU type: BCM4704
CPU Clock Speed: 200MHz
BUS Clock Speed: 33MHz
Memory Size: 64MB

Let’s see the current configuration with the command:

display current-configuration

To enter the configuration mode, type:


Continue reading “Configuring Huawei Quidway S3900 Switches”

Addition of ONT Huawei EchoLife HG8110 on Huawei SmartAX MA5683T

On the test, I wrote the profiles and added ONT Huawei EchoLife HG8110 to Huawei SmartAX MA5683T.

The first step is to connect to the Huawei SmartAX MA5683T and go into configuration mode:


Create ont-srvprofile:

ont-srvprofile gpon profile-id 14 profile-name "Huawei HG8110"
ont-port pots 1 eth 1
port vlan eth 1 translation 228 user-vlan 228

Create ont-lineprofile:

ont-lineprofile gpon profile-id 14 profile-name "Huawei HG8110"
tcont 4 dba-profile-id 11
gem add 1 eth tcont 4
gem mapping 1 0 vlan 228

We learn the serial number of ONT and the number of the card to which it is connected by typing the command to search for new ONTs:

display ont autofind all

Let’s go into the setup mode of the desired Gpon card (in the port of which the ONT is connected):

interface gpon 0/5

Now add ONT with the serial number:

ont add 3 17 sn-auth "414C434CF23D5EAF" omci ont-lineprofile-id 14 ont-srvprofile-id 14 desc OPISANIE
ont port native-vlan 3 17 eth 1 vlan 228 priority 0

Where number 3 indicates the Gpon port number to which the ONT is connected.

The number 17 means ID ONT and is listed next in order after added in the ONT configuration, the list of occupied IDs can be seen after exiting the Gpon card setup mode and typing the command displaying the entire configuration (for each gpon port, their IDs ONT):

display current-configuration
display current-configuration | include service-port

Let’s exit the Gpon interface configuration mode:


Add a service port that will give the Internet to ONT (the number 425 denotes the port service number and is taken from the free in the configuration):

service-port 425 vlan 228 gpon 0/5/3 ont 17 gemport 1 multi-service user-vlan 228

Save the configuration:


The standard IP address of Huawei EchoLife HG8110 is, the login is telecomadmin, the password is admintelecom.
In ONT, you do not need to configure anything.

See also:
Configuring Huawei SmartAX MA5683T through the console

How to find out the password for Huawei EchoLife HG8245

Configured today GPON ONT Huawei EchoLife HG8245C to OLT and it was necessary to go to its web interface to change the password on Wi-Fi, and the standard root login and password admin did not fit. I had to perform several manipulations.
Of course, to begin with, connect to any of the LAN ports, wait until the DHCP ONT is turned on, it will give out IP, such as or set it manually.
Connect via telnet to ONT IP, enter login root and password admin.
Then type the following commands one at a time:

cd /mnt/jffs2/
grep admin  myconfig.xml

As a result, the last command gives information about what is happening in the web interface:




Passwords can also be written on the device label. In the settings you can change the password, in this case the user will be useradmin and the specified password.
For HG8245, the standard administrative login and password telecomadmin \ admintelecom, for users – admin/admin. For Chinese HG8245C standard – telecomadmin \ nE7jA%5m.
There may be further passwords for telecomadmin:


See also: Create profile on Huawei SmartAX MA56XX for Huawei Echolife Hg8245

Adding ONT PICOTEL PU-G510 on Huawei SmartAX MA5683T

Suppose that we set up Huawei SmartAX MA5683T and added lineprofile/srvprofile using this instruction: Configuring Huawei SmartAX MA5683T through the console

Next, add ONT similarly as I wrote in the article Alcatel-Lucent I-010G

On the test after adding ONT PICOTEL PU-G510 to OLT Huawei SmartAX MA5683T, when connecting the computer to ONT – the Internet worked, when connecting the router – no.
Therefore, I still had to open the ONT web interface, pointing in the address line (login and password – admin), before registering the computer with a static IP
In the web interface, select the menu “Admin” – “GPON Settings”, where “OMCI OLT Mode:”, if using Huawei OLT – select “Huawei OLT Mode” and click “Apply Changes”.

See how I did it on video:

Etnernet ports are disabled on ONT Huawei EchoLife

I recently noticed a problem that, when ONT, the Huawei EchoLife HG8110, HG8120 and HG8120R watched the Ethernet ports shutdown about 30 seconds after the ONT was turned on.
At the same time, ONT continued to work, the optical connection did not disappear.
On the Huawei EchoLife HG8110 the link did not disappear, but the interface ONT stopped pinging.

The cause was defective power supplies.